Detailed setup guides (Serato, Traktor, Rekordbox)

Click on the DJ equipment you use below to see the corresponding illustrated setup guide: 

• DVS interface and Serato DJ Pro USB Integration (HID mode)
• Pioneer DJM-900NXS2 mixer & Rekordbox DJ
• Native Instruments Traktor Scratch Audio 6 DVS interface
• Native Instruments Traktor Kontrol Z2 mixer
• Mixfader and the Mixfader DJ app

Pioneer DJM-900NXS2 mixer & Rekordbox DJ

Setup overview

Setup steps

1. Power your Phase via USB or any 5V power supply to turn it on, and plug the RCA cables from the Phase outputs to the Line inputs (1&2 or 2&3 depending on your preference) of your DJM-900NXS2 mixer.

2. Plug the USB from your DJM-900NXS2 mixer to your laptop, and switch the Deck source selector on USB (A or B) to enable DVS Mode.

3a. Open Rekordbox, go to the Audio Settings and select “DJM900-NXS2” in the “Audio Interface Selector”. Then, open the setting utility and set the inputs you are using to “Control Tone Line”. You should also double check the same settings apply to the input channels you are using in the Rekordbox “Input Channels” setting.

3b. Go to the DVS tab in the Rekordbox settings, and make sure the DVS function is activated. Select “CDJs” instead of “Turntables” in the control hardware tab of the DVS settings.

3c. Make sure to select the audio routing according to the mixer decks you are using (1&2, or 2&3), and that the virtual decks are set on “Relative” mode.

4. Take the Remotes out of the Receiver, put them on your turntables and wait for the calibration to complete (allow the LEDs to turn solid). 

5. You are now ready to use Phase with your DJM-900NXS2 mixer and Rekordbox!

Native Instruments Traktor Scratch Audio 6 DVS interface

Setup overview

Setup steps

1. Power your Phase via USB or any 5V power supply to turn it on, and plug the RCA cables from the Phase outputs to the A and B inputs of your Traktor Audio 6 interface. Then plug the RCA cable from the A and B outputs of your Traktor Audio 6 into the “Line” inputs of your mixer.

2. Connect the Traktor Audio 6 to your laptop with its USB cable.

3. Open the Traktor Audio 6 Control Panel and make sure the “Input sens” is set on the “Line” signal.

4. Take the Remotes out of the Receiver, put them on your turntables and wait for the calibration to complete (allow the LEDs to turn solid).

5. Spin your turntables: you should see the perfect calibration circle on your Traktor decks. 

6. You are now ready to use Phase with your Traktor Audio 6 and Traktor Pro!

Traktor tips

• Make sure the Traktor signal is selected in Phase Manager’s “Configuration” tab.
• Make sure the Audio 6 is selected in the Traktor “audio setup” tab.
• Please note that the “calibration failed” message is just a display misinformation. To manually disable it, open Traktor's preferences and in the "Global settings" menu, uncheck the "Enable deck header warning" box (in the middle of the window).

Native Instruments Traktor Kontrol Z2 mixer

Setup overview

Setup steps

1. Power your Phase via USB or any 5V power supply to turn it on, and plug the RCA cables from the Phase outputs to the “Line” inputs of your Z2 mixer.

2a. Connect your Traktor Kontrol Z2 to your laptop with its USB cable.

2b. Set the PH/LN switch on “LN”, then click the Traktor button next to the PH/LN switch to enable DVS mode.

3. Take the Remotes out of the Receiver, put them on your turntables and wait for the calibration to complete (allow the LED turns solid).

4. Spin your turntables: you should see the perfect calibration circle on your Traktor decks. 

5. You are now ready to use Phase with your Traktor Kontrol Z2 and Traktor Pro!

 Traktor tips

• Make sure the Traktor signal is selected in Phase Manager’s settings (“Configuration” menu).
• Please note that the “calibration failed” message is just a display misinformation. To manually disable it, open Traktor's preferences and in the "Global settings" menu, uncheck the "Enable deck header warning" box (in the middle of the window).

Mixfader and the Mixfader DJ app

Setup overview

Requirements

• A sound card with audio inputs & outputs
• A USB to Lightning (or USB C) adapter
• A Device (smartphone or tablet) with Mixfader DJ App 
• A Turntable

Setup steps

1. Connect the audio outputs of your Phase to the audio inputs of your sound card.

2. Connect your speakers or headphones to your sound card output.

3. Launch the Mixfader DJ App and connect Mixfader to your device via Bluetooth.

4. Connect your sound card to your device using the USB/Lightning adapter.

5. Once your sound card is connected to your device, a pop up window will appear allowing you to select the “Serato Timecode Signal” and adjust the settings.

6. Take the Remotes out of the Receiver, put them on your turntables and wait for the calibration to complete (allow the LEDs to turn solid).

7. You are now ready to use Phase and Mixfader! You can now load tracks and start playing.